The system provides two types of the TSP for Optix OSN 1800 : TNF1TSPA & TNF1TSPB
Board Name | Description |
TSPA | 21-channel E1/T1 and 2-channel STM-1 service convergence and wavelength conversion board (75-ohm E1) |
TSPB | 21-channel E1/T1 and 2-channel STM-1 service convergence and wavelength conversion board (120-ohm E1) |
Board | Product Applicable-System Control Board-Initial Board Version Supported by System Control Board |
TNF1TSPA | 1800 I&II Compact-TNF1SCC-V100R002C00 |
TNF1TSPB | 1800 I&II Compact-TNF1SCC-V100R002C00 |
1800 I&II Compact-TNF3SCC-V100R006C20 | |
1800 V-TNF5UXCM/TNF5UXCME/TNF5XCH/ TNZ5UXCMS-V100R006C20 |
|
1800 II Enhanced-TNZ1UXCL-V100R007C10 |
The main functions and features supported by the TSP board are wavelength conversion, cross-connections, clock, and multiplexing of STM-1/E1/T1 signals.
Function and Feature | Description | |
Basic Function | Accesses 21 channels of E1/T1 electrical signals and two channels of STM-1 electrical/optical signals, and converts the input signals into two channels of STM-4/STM-16 optical signals or two channels of STM-1 electrical/optical signals. |
|
The optical ports on the WDM side provide the dual fed and selective receiving function (implemented through the electrical-layer SNCP). |
||
Working mode | Supports the SDH+WDM mode and SDH simplified mode. | |
NOTE: | ||
The working mode can be set to the SDH simplified mode only when the TNF1TSPB board works with the 1800 V system control board, 1800 II Enhanced system control board or 1800 I&II Compact TNF3SCC board. In this case, the board works in the SDH simplified mode by default. |
||
NOTE: | ||
When the TSP boards are interconnected, it is advised to configure the same working mode for them. |
||
Service type | STM-1: SDH services, the rate is 155.52 Mbit/s. | |
STM-4: SDH services, the rate is 622.08 Mbit/s. | ||
STM-16: SDH services, the rate is 2.488 Gbit/s. | ||
NOTE: | ||
The board does not support the STM-16 service when working with the TNF1SCC board. |
||
E1(75/120 ohms): PDH services, the rate is 2.048 Mbit/s. | ||
T1 (100 ohms): PDH services, the rate is 1.544 Mbit/s. | ||
NOTE: | ||
If the STM-1 electrical module is installed in a port, no electrical or optical modules can be installed in its adjacent ports. |
||
FEC function | Not supported | |
Alarms and performance events monitoring | Provides abundant alarms and performance events to facilitate management and maintenance of the equipment. |
|
Monitors performance parameters and alarm signals, including the monitoring of laser bias current, laser working temperature and optical power on the WDM side. |
||
Protection schemes | Supports SNCP protection | |
Overhead processing | Supports processing of section overheads of the STM-1/STM-4/ STM-16 signals. |
|
Supports the transparent transmission and termination of path overheads. |
||
Supports the setting and querying of the J0/J1/J2/C2/V5 byte. | ||
Supports processing of the AU/TU pointer. | ||
Supports one to four channels for DCC communication. | ||
Tributary function | Receives/Transmits 21 channels of 75-ohm/120-ohm E1 or 100-ohm T1 signals. |
|
Asynchronously maps E1/T1 signals into VC-12 containers. | ||
Processes overheads of VC-12 paths, and monitors alarms on the service paths. |
||
Provides inloop and outloop to test the quality of E1/T1 services or to locate a faulty point, facilitating the maintenance of the equipment. |
||
Provides the clock unit with two tributary clock sources contained in the first channel of signals and the twenty-first channel of signals output by the tributary-side port. |
||
Clock function | Supports the non-SSM protocol, standard SSM protocol and extended SSM protocol. |
|
Provides the synchronization clock required by the board. | ||
Provides the clock unit with seven synchronous timing sources contained in the two channels of signals output by the two client-side ports, two channels of signals output by the two WDM-side ports, one channel of signals output by the external clock port, and the first channel of signals and the twenty-first channel of signals output by the tributary-side port. |
||
Supports the three working modes: trace, hold-over, and free-run. | ||
Supports the control of the clock source priority levels. | ||
Supports the control of the clock source switching function. | ||
Processes and sets the S1 byte. | ||
Provides one 2048 KHz or 2048 kbit/s external clock ports, of which the impedance is 120 ohms. The 2M export operation exports system source clocks only. |
||
Supports tributary retiming. | ||
Loopback | Supports inloop and outloop on a WDM-side VC-4 path. | |
Supports inloop and outloop on a client-side VC-4 path. | ||
Supports inloop and outloop on each tributary path (1-21 paths). | ||
Regeneration board | LWX2 | |
ALS function | Not supported | |
ESC function | Supported | |
LPT function | Not supported | |
PRBS test | Supports the PRBS function on the client side and tributary side. | |
NOTE: | ||
The PRBS function on the client side is supported only when the client-side service type is STM-1, and on the tributary side is supported only when the client-side service type is E1/T1. |
||
Cross-connect function | Supports 11x11 cross-connections of VC-4 signals, or 693x693 full cross-connections of VC-12 signals. |
|
Supports two cross-connections on the WDM side of the TSP board to the client side of the LQM2 board. |
||
Supports cross-connections of STM-1/STM-4/STM-16 services between paired slots, cross-connections between transverse slots, and cross-connections between diagonal slots. For details, see Slots for Cross-Connect Boards. |
||
WDM specifications | Supports ITU-T G.694.1-compliant DWDM specifications and ITU-T G.694.2-compliant CWDM specifications. |
Optix OSN1800 I & OSN1800 II Optical Transponder Board as below:
TNF1CE6 6-port encrypted multiplexing optical wavelength conversion board
TNF1CP6 6-port CPRI multiplexing optical wavelength conversion board
TNF2CP6 6-port CPRI multiplexing optical wavelength conversion board
TNF1CP8 Enhanced 8 x Multi-rate Ports Wavelength Conversion Board
TNF2ELOM Enhanced 8 x multi-rate ports wavelength conversion board
TNF2LQM2 (VA8) Double 4 x multi-rate ports wavelength conversion board
TNF1LQPL OLT side 4 port GPON/STM-16/OTU1 access wavelength conversion board
TNF1LQPU ONU side 4 port GPON/STM-16/OTU1 access wavelength conversion board
TNF1LSPL OLT side single port GPON access wavelength conversion board
TNF1LSPR Single port GPON extension REG board
TNF1LSPU ONU side single port GPON access wavelength conversion board
TNF1LSX 10 Gbit/s wavelength conversion board
TNF2LSX 10 Gbit/s wavelength conversion board
TNF1LWX2 Double arbitrary bit rate wavelength conversion board
TNF1TSP 21-channel E1/T1 and 2-channel STM-1 service convergence and wavelength conversion board
Comments
Post a Comment